Typical overview of the Mezzanine floor lift: The lift will be constructed using a single mast which must be bolted to the building block-work to provide additional support to the load legs. The lift platform will measure approximately 1500mm wide by 1250mm deep and will close down over the legs.......

The lift will be constructed using a single mast which must be bolted to the Mezzanine floor RSJ through the floor

The lift platform will measure approximately 1400mm wide by 1200mm deep and will close down over the legs

The clear working platform area will be 1340mm x 1140mm......

The lift will be constructed using a single mast which must be bolted to the Mezzanine floor RSJ through the floor

The lift platform will measure approximately 1400mm wide by 1200mm deep and will close down over the legs

The clear working platform area will be 1340mm x 1140mm......

CONTROLS - A control panel will be fitted on both the lower and upper floor.

SAFETY EDGE - There is a built in safety function in the safety frame. If the Safety Frame is touched on its way down, the Lift stops immediately. To continue lowering, the table has to be raised a little to be able to lower again.......

Typical overview of the Mezzanine floor lifter: The lift will be constructed using a single mast which must be bolted to the building block-work to provide additional support to the load legs. The lift platform will measure approximately 2140mm wide by 1540mm deep and will close down over the legs. The platform will feature 1100mm high rails on all sides and a double outwards opening gate. The gates will be spring loaded and will lock with a gravity system but will also be sensed to prevent platform movement if the gate is open.......

Typical overview of the Mezzanine Goods lifter: The lift will be constructed using a single mast which must be bolted to the building block-work to provide additional support to the load legs. The lift platform will measure approximately 1500mm wide by 1500mm deep and will close down over the legs. The platform will feature 1100mm high rails on all sides and a single outwards opening gate on the right-hand side of the mast. The gate will be spring loaded and will lock with a gravity system but will also be sensed to prevent platform movement if the gate is open......

The Manual Handling Solutions Mezz Lift is a robust and versatile platform lift for handling all sorts of loads up to approx 750kg safely and efficiently between floors such as ground floor and mezzanine level. It offers users a cost effective solution to comply with Manual Handling Regulations and reduce the risk of injury to employees......

The Mezz Lift is a robust and versatile platform lift for handling loads up to 300kg safely and efficiently. It offers users a cost effective way to comply with manual handling regulations and reduce the risk of injury to employees. The entire handling process can be undertaken by a single person without any manual lifting to promote safety and productivity. A unique hold-to-run system promotes safety by stopping the lift whenever the control lever is released.......

Control points will be mounted at both the ground and mezzanine levels attached to the guarding. Both control points will feature latching control buttons; Raise, Lower & E-stop SAFETY TRIP BAR Aluminium safety frame with built in safety function.

If the safety frame is touched on its way down, the Lift stops immediately. To continue lowering, the table has to be raised a little to be able to lower again. MAINTENANCE Standard safety legs are provided to support the scissor lift mechanism in the raised position and must be deployed for all servicing and maintenance work......

The lift platform will measure approximately 1350mm wide by 1250mm deep and will close down over the legs of the masts

The clear working platform area will be 1290mm x 1130mm ......

2 x controls (located at ground and 1st floor levels) UP & DOWN latching hand control units with EMERGENCY STOP button and 4 meter long cable

1100mm high handrails to both long sides and 1 short side Single outward opening gate on other short side, electrically interlocked type 1 ......

We offer scissor lift which has a 1300mm x 800mm lift platform size, which will have a 1200mm x 720mm usable area, narrowing to approx. 650mm width through the drop down barrier.

1000Kgs capacity as standard, but would be de-rated to 500Kgs when handling goods.......

The lift is to be positioned on the end of the racking so will be no wider than 800mm. The platform size will be 450mm x 850mm (loading onto the 450mm side) and will dock at around 900mm from the floor at both levels. There will be a slam shut, single gate at both levels as demonstrated in the attached drawing.......

The lift is to be positioned on the end of the racking so will be no wider than 800mm. The platform size will be 450mm x 850mm (loading onto the 450mm side) and will dock at around 900mm from the floor at both levels. There will be a slam shut, single gate at both levels as demonstrated in the attached drawing.......

Table will be supplied with a remote power pack for ease of change over, should a fault occur. A spare power pack will also be provided.......

Goods Lift, with maximum working load 500kg, fully enclosed in a self supporting mesh shaft. The platform will be increased to 1350mm x 1600mm to accommodate clients request for loading a pallet or 4 trolleys.......

Goods Lift, with maximum working load 250kg, fully enclosed in a self supporting mesh shaft. The lift will have three stops; ground, first tier mezzanine and second tier mezzanine. At each level the entrance to the lift will be via 2000mm clear high gates fitted with electrical interlocks which will prevent the gates from being opened unless the platform is docked at the appropriate level.......

1100mm high mild steel handrails complete with mid rail and 150mm high kick plates suitable for mounting along both long sides of the scissor lift platform by the contracted installer. One short end to be fitted with a simple drop down barrier with micro stop/go switch.......

Mezz Lift Goods Lift , with maximum working load 250kg which is to be fixed back to the existing side wall, guarded two sides at the lower level and three sides at the upper level. The platform size will be 800mm x 1000mm, guarded three sides to suit loading on and off the same side........

Scissor Table style Goods Lift designed and installed at Bicester Village for Prada. Manual Handling Solutions were approached by Gregori Chiarotti Architects in offering a solution for the delivery of Goods to the Prada store at Bicester Village......

Mezz Lift, with maximum working load 250kg, fully enclosed in a self supporting mesh shaft. The platform will be 1650mm x 850mm to allow two trolleys to be transported at the same time.

Additional feature
The Mezz Lift will be fitted with a fall arrest block on to the platform, independent of the existing chains which would hold the platform in place in the event of a catastrophic failure......